Action Electronics

Speed Controllers

Home »  Speed Controllers

P68A pico 1A Microcomputer, linear acceleration SPEED CONTROLLER

Pico is the smallest controller ACTion has ever produced. It should be run from 4.8 Volt (NiMH) to 6 Volt (Alkaline) batteries from where it gets the power for the motor – it plugs in like a servo). Ideal for small plastic kit models. Overall case size 34mm x 24.5mm x 16mm. Weight with case 16g. Can be left out of case for really tiny models, when weight is 9g.

P68S Variable Speed Brushless Fan Controller

Designed for air-cooling of motors, ESCs etc. Runs in the correct direction in proportion to main motor throttle (connects to Rx via Y-lead). No extra power supply required. Includes speed controller, 40mm fan, splitter connector ; ready-built.

P78 CONDOR 2 AUTOSET Computer SPEED CONTROLLER

2A speed controller for small scale model boats; recommended for 360/385 type and similar motors. 2 to 12 volts motor battery range; can be adapted easily to run motor from Rx supply. AUTOSET centre stick setting and fixed gentle acceleration. External size 41mm x 31mm x 20mm. Weight 26g. NOTE: This unit is not fitted with Battery Eliminator Circuitry (BEC).

P79 CONDOR 10/2 AUTOSET Computer SPEED CONTROLLER

Computerised 10A speed controller for scale model boats, recommended for 380/385 & SPEED 400 type motors. Main motor drive voltage range 2 to 12 Volts. AUTOSET centre stick setting; selectable gentle/rapid acceleration. Motor stops if signal lost or receiver switched off. Screw terminal block connections for Motor and Power. External size 53.5mm x 37.5mm x 23mm (plus approx 8mm for the heat-sink). P79S version suits 7- to 12-pole motors. NOTE: This unit is not fitted with Battery Eliminator Circuitry (BEC).

P80 CONDOR 20/2' AUTOSET Computer SPEED CONTROLLER

Computerised 20A speed controller for scale model boats, recommended for 540/545 & SPEED 600 type motors. Main motor drive voltage range 2 to 12 Volts. AUTOSET centre stick setting; selectable gentle/rapid acceleration. Motor stops if signal lost or receiver switched off. Screw terminal block connections for Motor and Power. External size 63.5mm x 43.5mm x 25mm (plus approx 6mm for the two heat-sinks). P80S version suits 7- to 12-pole motors. NOTE: This unit is not fitted with Battery Eliminator Circuitry (BEC).

P81 CONDOR 5 AUTOSET Computer SPEED CONTROLLER

Computerised 5A peak speed controller for scale model boats; recommended for 380/385 type motors. 2 – 12V main motor battery range. AUTOSET centre stick setting; selectable gentle/rapid acceleration. Motor stops if signal lost or receiver switched off. Screw terminal block connections for Motor and Power. Overall size 53.5mm x 37.5mm x 23mm. NOTE: This unit is not fitted with Battery Eliminator Circuitry (BEC).

P98 HIGH-POWER ELECTRONIC SPEED CONTROLLER

P98 was developed primarily at the request of our Australian agents, Darke Horse Model Supplies, to use with their fan-cooled, planetary-geared 785 motors. These run on power supplies from a humble 12v up to a mind-boggling 20 cells (30v+), although their current consumption is relatively modest. Our Design Consultant, Dr Tim Fawcett, has broadened the specification and also included some very useful features, with the result that the P98 is probably the most ‘controllable’ speed controller on the market anywhere in the world. Specifications are: Motor voltage 12v Min; 32v Max Motor Current 30A Max Continuous; 140A Surge Rx Supply voltage 5.0v Min/6.0v Max User-selected functions (via on-board DIL switches): 1) Standard/Offset neutral transition speed 2) Linear/Non-linear acceleration curve 3) Standard/Extended speed range 4) Normal width/Wide neutral (dead-band). Case size 74mm x 50mm x 28mm (+30mm for heat-sink fins). Screw terminal connections. Accessories (Available separately) P99 In-line 5v Voltage Regulator P98W Heat-sink water-cooling set